云 發 布-
想要真正了解軟管泵攔水帶成型機量少也做產品的魅力嗎？這個視頻將以其無與倫比的視聽效果，讓您仿佛置身于產品的核心之中，感受其獨特的魅力。
以下是:軟管泵攔水帶成型機量少也做的圖文介紹
不銹鋼軟管泵的保養：不銹鋼泵緊固端面螺栓時，不銹鋼泵用力要對稱均勻；邊緊邊盤動轉子。若遇到卡澀，不銹鋼泵應松掉螺栓重新緊。電泵泵驅動軸不能承受任何徑向垂直力，皮帶、鏈條、齒輪等側向驅動方式禁止使用。底板強的驅動軸與電機軸的連接采用彈性聯軸器或鏈式聯軸器。軟管泵的齒輪油度要夠，不要時間長了泵的底板一軟，造成電機與泵不對中而損壞泵。弄清楚泵的允許高轉速和現場工作高轉速。務必讓流體進到入口，盡量不要干轉和空轉。
為了讓用戶用上滿意的產品，豫信致誠機械設備有限公司(保定分公司)建立了嚴苛的 混凝土拋丸機質量驗收的標準，還擁有先進的操作技術，為客戶提供精準的售后服務，以遠高于驗收標準的工藝確保 混凝土拋丸機的質量。
軟管泵工作原理：
一根內壁光滑，強度可靠的特制橡膠軟管安裝在泵體內部，通過一對壓輥沿著軟管旋轉擠壓，這樣的 旋轉使得介質往一個方向輸送而不會倒流，軟管在輸送介質之后，由被壓扁軟管的自身彈性和側導輪的強制下，軟管恢復原狀，此時，軟管內產生高真空將介質再次吸入管腔，然后介質在隨之而來的壓輥擠壓下從軟管內排出，如此周而復始，介質不斷的被吸入和排出。目前產品使用溫度為≤100℃。根據用戶需要可以開發使用溫度在120℃的軟管泵軟管產品。
Working principle of hose pump:
A special rubber hose with a smooth inner wall and reliable strength is installed inside the pump body. It is rotated and squeezed along the hose by a pair of pressure rollers. This rotation allows the medium to be transported in one direction without flowing back. After that, due to the elasticity of the flattened hose and the force of the side guide wheels, the hose returns to its original state. At this time, a high vacuum is generated in the hose to suck the medium into the lumen again, and then the medium is pressed by the subsequent pressure roller. It is discharged from the hose under the squeeze, and so on and on, the medium is continuously sucked in and discharged. The current product temperature is ≤100 ℃. According to user needs, we can develop hose pump hose products with a temperature of 120 ℃.
一根內壁光滑，強度可靠的特制橡膠軟管安裝在泵體內部，通過一對壓輥沿著軟管旋轉擠壓，這樣的 旋轉使得介質往一個方向輸送而不會倒流，軟管在輸送介質之后，由被壓扁軟管的自身彈性和側導輪的強制下，軟管恢復原狀，此時，軟管內產生高真空將介質再次吸入管腔，然后介質在隨之而來的壓輥擠壓下從軟管內排出，如此周而復始，介質不斷的被吸入和排出。目前產品使用溫度為≤100℃。根據用戶需要可以開發使用溫度在120℃的軟管泵軟管產品。
Working principle of hose pump:
A special rubber hose with a smooth inner wall and reliable strength is installed inside the pump body. It is rotated and squeezed along the hose by a pair of pressure rollers. This rotation allows the medium to be transported in one direction without flowing back. After that, due to the elasticity of the flattened hose and the force of the side guide wheels, the hose returns to its original state. At this time, a high vacuum is generated in the hose to suck the medium into the lumen again, and then the medium is pressed by the subsequent pressure roller. It is discharged from the hose under the squeeze, and so on and on, the medium is continuously sucked in and discharged. The current product temperature is ≤100 ℃. According to user needs, we can develop hose pump hose products with a temperature of 120 ℃.
